jack and boring specs

REQUIREMENTS FOR THE DESIGN AND …

jacking, driving, boring, drilling, tunneling or other approved means, (hereinafter collectively referred to as, jacking, boring, etc.) in conformance with the requirements and specifications cited throughout this document. Water jetting will not be permitted. No open cuts will be

Get A Free Quote

Section 37 BORING AND JACKING 37-1 …

City of Sanger Standard Specifications 7/08 Page 240 Section 37 BORING AND JACKING 37-1 GENERAL This section covers tunneling and/or boring and jacking of casing pipe and furnishing and placing water pipe, sewer or drain pipe (conveyance pipe) within the casing pipe (two-pass system) or direct jacking of conveyance pipe (single …

Get A Free Quote

SECTION 556 JACK AND BORE 556-1.1 Scope …

SECTION 556 JACK AND BORE 556-1 Description. ... Bore (J&B), also known as auger boring. Micro tunneling (MT) is also included in the category of J&B for purposes of specifications. 556-1.2 General: J&B is a method for installing a product (often called a casing) that may serve as a direct conduit for liquids or gases, or as a duct for carrier …

Get A Free Quote

SECTION 817 JACKED AND BORED PIPE / …

shall be minimal to complete the jack and boring operations. Redrill pilot hole when bore does not - Redrill pilot hole when bore does not - meet specifications.

Get A Free Quote

Auger Boring - Frequently Asked Questions

Auger Boring - Frequently Asked Questions. Auger Boring or jack and bore is perhaps that most recognizable and most common trenchless application. It is generally well understood, and when good design and responsible contracting combine, the success rate is very high.

Get A Free Quote

JACK AND BORE - Florida Department of …

SECTION 556 JACK AND BORE . 556-1 Description. 556-1.1 Scope of Work: The work specified in this Section documents the approved construction methods, procedures and materials for Jack and Bore (J&B), also

Get A Free Quote

SPECIFICATION 330524: BORING AND …

October 2017 Specification 330524 | 1 SPECIFICATION 330524: BORING AND JACKING . PART 1.0 GENERAL 1.1 DESCRIPTION 1.1.1 The work of this specification includes all labor, machinery, construction equipment and appliances

Get A Free Quote

SECTION 15070 JACKING AND BORING PART …

MDWASD 1/1999 15070 - 1 R-1 SECTION 15070 JACKING AND BORING PART 1 - GENERAL 1.01 SCOPE OF WORK A. The Contractor shall furnish all labor, material, equipment, and appurtenances required to

Get A Free Quote

APPENDIX G SPECIFICATIONS - Virginia …

The jack and bore method shall be applicable for installing concrete pipe 12 through 108 inches in diameter and smooth-wall steel pipe 12 3/4 through 48 inches in diameter.

Get A Free Quote

Specifications - NCDOT

Specifications Standards Specifications, Roadway Standard Drawings, Pay Items, and Other Resources Connect NCDOT > Resources > Specifications 2018 Specifications and Special Provisions

Get A Free Quote

2012 Roadway Standard Drawings - Connect …

If any part of the "Detail Drawings" are required, please insert ALL drawings in the Roadway Plans. DO NOT cross out any drawings in the set.

Get A Free Quote

MDS Boring & Drilling

bore & jack Bore & Jack uses a combination of methods. A guided pilot is run with a boring machine the length of the bore. After the pilot is run, the steering head is removed and a reamer the size of the line pipe is installed on the drill stem. As the drill stem is retracted and the bore is reamed, the line pipe is advanced into the bore a ...

Get A Free Quote

Boring Machine Operation & Safety …

Boring Machine Operation & Safety Instruction Manual WARNING Unsafe use of this equipment could result in serious injury or death. This manual con-

Get A Free Quote

Std Plans and Specifications Cover - Marina …

marina coast water district october 2007 01045-1 standard specifications section 01045 existing facilities part 1 - general a. description

Get A Free Quote

SPECIFICATIONS FOR BORING AND …

Boring and Subsurface Exploration Drill Specification March 2010 1 . SPECIFICATIONS FOR BORING AND SUBSURFACE . EXPLORATION DRILL MACHINE. ITEM: One relatively lightweight combination auger, core, and rotary type boring …

Get A Free Quote

002445 - Jack and Bore - Charlotte County

CCU STANDARD SPECIFICATIONS Section 002445 JACK AND BORE Effective Date: Nov. 1st, 2011 Page 1 of 6 PART 1 - GENERAL It is the intent of this specification to provide the requirements for any jacking-boring for the

Get A Free Quote

DIRECTIONAL BORING SPECIFICATIONS PART …

The directional boring equipment shall consist of a directional boring rig of sufficient capacity to perform the bore and pullback the pipe, a boring fluid mixing & delivery system of sufficient capaci-

Get A Free Quote

MDS Boring & Drilling

bore & jack Bore & Jack uses a combination of methods. A guided pilot is run with a boring machine the length of the bore. After the pilot is run, the steering head is removed and a reamer the size of the line pipe is installed on the drill stem. As the drill stem is retracted and the bore is reamed, the line pipe is advanced into the bore a ...

Get A Free Quote

Updated: JUN 2018 2016 ROAD and BRIDGE …

Updated: JUN 2018 — 2016 ROAD and BRIDGE SPECIFICATIONS (Division III) — Saved: 05/23/2018 8:55 PM TOC, VDOT Web, OVDOT, I, II, III, IV, V, VI, VII, VIII, 2018 Supplement, 2016 Spec Book 3-1 2016 ROAD AND BRIDGE SPECIFICATIONS

Get A Free Quote

NORFOLK SOUTHERN CORPORATION

Culvert installed by the Jack and Bore method shall be limited to either Corrugated Steel Pipe or Smooth Steel Pipe. Reinforced concrete pipe will not be allowed to be

Get A Free Quote

STANDARD SPECIFICATIONS -

C. Boring and Jacking: Method of installing casing pipe by cutting, hand mining, or boring an opening in soils material, simultaneously forcing casing pipe through it …

Get A Free Quote

Typical Jack & Bore Construction No.

File: c Date: 12/10/03 Rev. A No.: Typical Jack & Bore Construction 1 Auger is in 10' lengths, pit length is bore machine length plus work room plus multiples of …

Get A Free Quote

DESIGN AND CONSTRUCTION STANDARD …

3.1 Soil Investigation 11 3.1.1 General Requirements 11 3.1.2 Location 11 3.1.3 Sampling 11 3.1.4 Boring Logs 11

Get A Free Quote

SECTION 02400 UTILITY JACKING AND …

Caltrain Standard Specifications 02400 -1 September 30, 2011 UTILITY JACKING AND BORING SECTION 02400 UTILITY JACKING AND BORING PART 1 – GENERAL 1.01 DESCRIPTION A. Section includes specifications for jack and bore installation of pipe, casing, or conduit. 1.02 SUBMITTALS A. Obtain Engineer's approval of the following submittals: 1. Submit working drawings describing the proposed jack …

Get A Free Quote

Standard Details - Broward County, Florida

153 jack and bore profile 154 casing pipe detail jack and bore 155 jack and bore pipe details 167 conflict maintenance access structure 182 restoration of roadway cut for parallel utility installation 183 192 typical section through swale pipe to be abandoned pipe to be abandoned (live line 4" and larger) 194 bollard 205 figure nos. title filling and …

Get A Free Quote